Glory played 9A, March 30 and glory 30s on the same stage, as a "entry machine", has been equipped with 820 glory 30s to grab the "Head". Simple searched glory game 9A, the evaluation is mixed, it is known that it is "high quality entry", and it is impossible to sell the price and configuration. Curiosity urges us to buy and dismantle, this glory is playing with the biggest highlights of the 9A.
Dismantle
Before dismantling, it is still taken out, and the plastic material trapping uses the three card design, and there is no waterproof ring on the calorie, and there is a Chinese logo to prevent insertion. Support dual NANO-SIM card and a MicroSD card.
Heat the rear cover with the hot air gun, and the binding of the lens opens the back cover. It is to be noted that the fingerprint sensor is connected to the connection soft board through the ZIF interface, and disconnects the connector to remove the rear cover.
Glory playing 9A rear cover Use black adhesive fit to fix. The inside of the rear cover is attached to graphite heat stickers, and there is a foam pad to support the gap between the buffer rear cover and the battery. There is a screw on a screw and a tap label.
In the middle frame, the support is secured by the card slot, and use the crowbar along the snap. Four-week filled with soft board antenna in the box.
The main, sub-plate and speaker modules are fixed by screws, and dismantling is easy. A waterproof label is posted on the speaker module and the motherboard. The corresponding handset position is posted on the motherboard.
It can also be seen here to see the easy-to-demolith hand on the double-sided viscous film of the fixed battery, which can easily dismantle the replacement battery according to the instruction.
Remove the main pair, the battery, the front and rear cameras. The motherboard and the sub-board are connected by the FPC soft board and the coaxial line. The USB connector on the sub-board, the headphone interface, and the light sensor have different colors of silicone sleeves for protection. There is a pink heat conductive silicone between the motherboard shield and the inner support.
The right button soft plate, the handset and the vibrator are secured to each mounting position. In the box, the corresponding card slot position has graphite hot stickers.
Between the screen and the middle box is fixed by the adhesive, the edge has a rolling landing gear. The upper portion of the middle frame is attached to the graphite heat preparation film, the lower portion possessed the foam material and the small amount of graphite cooling film, and there is an insulating tape above the device on the screen soft board.
The screen uses the 6.3-inch 1600x720 resolution of Shenzhen Tongda 1600x720 resolution full screen.
From the dismantling, the glory playing 9A machine is fixed by 17 screws, standard three-segment design. The internal label labels and waterproof labels are labeled; the CPU is heat-free by heat-conducting silicone. Integration to see glory playing 9A's largest highlights may be 5000mAh big batteries, or Liaotai MT6765 processor?
After disassembling, let's take a look at the IC information of the whole machine.
The main IC of the motherboard:
1: Media TEK-MT6765-Barn processor
2: Micron-4GB memory
3: Media tek-mt ***** - wifi / bt / GPS / GLONAS / FM
4: Skyworks-sky ***** - RF power amplifier
The main IC on the back of the motherboard (below):
1: SanDisk-SDINBDA4-64G-64GB flash memory
2: Media tek- MT **** - Power Management
3: Media tek-mt **** - RF transceiver
4: Goertek-Microphone
From the design plan, the glory 9A machine chip uses the UNACD solution, the LCD screen + back fingerprint recognition scheme is used, and the cost is lower than the OLED screen + screen. Thus, effective control of costs. Of course, the machine IC is far more than these, the whole machine BOM moves Ewistech, search glory to play 9A to view.
Top equipment now on Ewistech ...
OPPO - RENO4 Pro
Samsung - Galaxy A51 5G
NUBIA - Red Magic 5G
Reprinted from ewistech.
Our other product:
