"NXP's qn9080-001-m17 is a subminiature pre certified Bluetooth 5.0 MCU that supports ble and NFC and integrates NFC ntag ® Connectivity. Subminiature devices are based on qn9080 chip and nt3h2211 chip. The qn9080 chip is based on arm cortex-m4f MCU and has a special fusion sensor coprocessor (FSP). The power consumption is further reduced due to the unloading of complex mathematical algorithms from the hardware; Nt3h2211 chip is an NFC forum type 2 tag compatible IC with I2C interface, which provides the fastest and cheapest way to increase tap and go connectivity. Qn9080-001-m17 also integrates 32mhz and 32.768 kHz crystals, 2.4GHz optimized antenna and necessary components for running qn9080 system. It integrates 512KB flash memory and 128KB ram, providing a complete solution that requires ble wireless connection and fast pairing with ntag. It has a small number of external components, which can reduce the size, complexity and development time of the system. With transmission power up to + 2dbm and reception sensitivity of - 92.7dbm (1Mbps mode) and - 89dbm (2Mbps mode), it is mainly used in health and medical equipment, sports and bodybuilding trackers, building and home automation, retail and advertising beacons. This paper introduces the main characteristics and advantages of qn9080sip. The main characteristics of qn9080 are ntag and integrated 2.4GHz antenna, qn9080-001-m17-advanced HW block diagram, qn9080-001-m17 evaluation board, qn9080dk main characteristics, circuit diagram and PCB design diagram.
The QN9080-001-M17 is a fully certified device supporting BLE and NFC. It has ultra-low power consumption， highly integrated with rich feature sets， fully FCC/CE/IC/MIC certified. The QN9080-001-M17 supports Bluetooth 5， and it is intended for ultra-small， portable connected wireless applications.
This ultra-small device is based on QN9080 die and NT3H2211 die. QN9080 is powered by an Arm Cortex-M4F， and has a dedicated fusion sensor co-processor （FSP） to further reduce power consumption by off-loading complex math computations to the hardware. 512 KB of on-board flash and 128 KB SRAM provide enough room and flexibility for complex applications. NT3H2211 is NFC Forum Type 2 Tag compliant IC with I2C interface， which supplies the fastest， least expensive way to add tap-and-go connectivity to just about any electronic applications.
The QN9080-001-M17 also integrates 32 MHz and 32.768 kHz crystals， a 2.4 GHz optimized antenna， and necessary components for QN9080 system to run. It offers a complete solution for applications requiring BLE wireless connectivity and fast pairing with NTAG as an option. Its low external component count reduces overall system size， complexity and shortens development time.
Main features and advantages of qn9080sip:
Main features:
Bluetooth 5.0 certified
Integrated antenna
Integrated 32 MHz and 32.768 kHz crystals
32-bit Arm Cortex-M4F core at 32 MHz
512 KB flash
128 KB RAM
TX power： up to +2 dBm
RX sensitivity： -92.7 dBm in 1 Mbps mode and -89 dBm in 2 Mbps mode
True single-chip Bluetooth Low Energy （v5.0） SoC solution：
Integrated Bluetooth LE radio， protocol stack and application profiles
Support central and peripherals roles
Support master/slave concurrency
Support 16 simultaneous links
Support secure connections
Support data packet length extension
48-bit unique BD address
-92.7 dBm in 1 Mbps mode and -89 dBm in 2 Mbps mode
TX output power from -20 dBm to +2 dBm
Very low power consumption：
Single 1.67 V ~3.6 V power supply
1 A power-down mode， to wake up by GPIO
2 A power-down mode， to wake up by 32 kHz sleep timer， RTC and GPIO
4 mA RX current at 3 V supply in 1 Mbps
Ultra Low power Bluetooth Low Energy 5.0 module
3.5 mA TX current at 0 dBm TX power at 3 V supply in 1 Mbps mode
Interface：
32 General-Purpose Input/Output （GPIO） pins， with configurable pull-up/pull-down
resistors
8 external ADC inputs （shared with GPIO pins）
2 Analog Comparator input pins （share with GPIO pins）
Single power supply 1.67 V to 3.6 V
Operating temperature range -40℃ to +85℃
6 x9.7x1.17 mm LFLGA package
Main features of qn9080:
True single-chip Bluetooth Low Energy （v5.0） SoC solution
Integrated Bluetooth LE radio， protocol stack and application profiles
Supports central and peripherals roles
Supports master/slave concurrency
Supports 16 simultaneous links
Supports secure connections
Supports data packet length extension
Wifi/Bluetooth LE coexistence interface
48-bit unique bluetooth device address
RF
Fast and reliable RSSI in 1 dB step
TX output power from 20 dBm to 2 dBm
Single-ended RF port with integrated balun
Generic FSK modulation with programmed data rate from 250 Kbps to 2 Mbps
Compatible with worldwide radio frequency regulations
Very low power consumption
Single 1.67 V to 3.6 V power supply
Integrated DC-to-DC buck converter and LDO
1.0 A power-down 1 mode， to wake up by GPIO
2.5 A power-down 0 mode， to wake up by 32 kHz sleep timer， RTC and GPIO
3.5 mA RX current with DC-to-DC convertor enabled at 3 V supply in 1Mbps mode
4 mA TX current at 0 dBm TX power with DC-to-DC converter enabled at 3 Vsupply in 1 Mbps mode
Arm Cortex-M4 core （version r0p1）
Arm Cortex-M4 processor， running at a frequency of up to 32 MHz
Floating Point Unit （FPU） and Memory Protection Unit （MPU）
Arm Cortex-M4 built-in Nested Vectored Interrupt Controller （NVIC）
Serial Wire Debug （SWD） with six instruction breakpoints， two literal comparators，and four watch points， including serial wire output for enhanced debug capabilities
System tick timer
On-chip memory
512 KB on-chip flash program memory and 2 KB page erase and write
128 KB SRAM
256 KB ROM
ROM API support
Flash In-System Programming （ISP）
Our other product:
