Speaking of overclocking, players who are familiar with DIY know that CPUs, graphics cards and memory can overclock, overclocking can make the performance of hardware brings different levels of improvement, so many enthusiasts prefer to have a stronger performance to hardware overclocking.
However, today we are not the CPU is not a graphics card, but is not paid by the player. In fact, silicone also plays an important role in the whole machine. If you use it, you can make the radiator to play performance, not only the temperature of the CPU can be lower, but the speed of the fan can also reduce some, thereby obtaining lower noise It can be said that it is "overclocking" to the heat sink. For newcomers, silicone use seems to be simple, but also pay attention to the difference in detail not only the difference between rookies and old birds, but also affects the host's experience.
Apply to see the position
The newly bought radiator has plastic stickers in the contact of the CPU. This layer of stickers generally write the words in the predecessor, but some users may be careful, or the stickers are the English words players can't understand, The radiator is fixed together with the sticker.
The heat sink is to heat the heat and heat dissipation, in order to have a better thermal conductive effect, silicone is applied in the slit. If there is an article blocking heat transfer, it will seriously affect the use effect of the heat sink.
The role of the radiator bottom sticker is to keep the bottom of the neat and clean, which can avoid scratches or bumps that may cause during transportation, resulting in uneven surface, can reduce dust or debris when the user is in use, can provide better heat dissipation Effect.
Therefore, the CPU heat sink must be cleaned up and then installed. The plastic sticker that comes with the factory will have to reveal that the surface of the CPU should be cleaned, and the neat surface is a good heat dissipation.
Meng Xin has caused severe consequences between the main board and the CPU
Also add, silicone must be applied between the CPU and the radiator, do not apply between the CPU and the main board, the consequences of the wrong, there is a similar funny map not to imitate.
Don't be too much to fill the gap
We all know that silicone is used to conduct heat, but there is still a player who will mistake the better the silicon-lipid, and the thermal conductivity of silicone stain is far less like a metal material, especially copper and aluminum, such as the heat sink. Silicone should be mainly used to fill the gap and cannot be applied too much.
Usually the CPU heat sink will come with a pack or a tube silicone, but this is not allowed to use the user once, and some radiator can be used for 5-6 times or more times, if one is complete It will be too much on the CPU or the radiator, and the thinner silicone is applied, the better.
When the heat passes from the CPU to the fin to the heat sink, it will pass through many links, where the heat dissipation effect is lowered from the CPU cover to the bottom surface of the heat sink, and the dissipated silicone is to strengthen thermal conductivity. Therefore, the connection between the heat sink and the CPU is mainly in direct contact with metal, and the heat-conducting silicon contact is adjusted.
Understand the effect of silicone, everyone can easily know that silicone is applied as much as possible, and then gently transfer silicone after installing the radiator, and removes excess silicone fat, let heat dissipation Can better conduct heat.
Apply small skill to eliminate problems
There are still some tips about silicone disconation. We know that the silicon is thin as possible, and it is necessary to take a tool when it is applied. The high-end silicone will come with a scraper, which allows silicon to be very thin. Players can also use cardboard homemade scrapers, and the effect is equally different.
In addition to the best as possible, it is necessary to ensure that the silicone having no bubbles or impurities are applied, affecting the heat dissipation. Generally, new radiators or silicone is rarely abnormal, but the old heat sink may be stained with dust or oil, and the silicone that has been demolished may also be mixed into impurities, which requires us to manually when installing the radiator. Exclude possible problems.
Bubbles or grease will affect the adhesion of silicone on the surface of the heat sink, slowing the heat transfer, and impurities cause a gap between the heat sink and the CPU, affecting the use of the heat sink, some impurities will even leave the contact surface. Scratches, further affect heat dissipation performance.
After installing the heat sink, the contact surface of the radiator and the CPU is applied. After the silicone is applied, the surface is scratched, and the silicone can be applied to the silicone, and the silicone surface is observed, and there is no bubble impurities, vague can be used. It is a suitable coating that the heat sink is thin.
Attention should be noted when coating silicone, do not apply silicone to the motherboard, if excess silicone is wiped on other hardware to clean up, avoid other hardware.
Don't force your miracle
The installation of the heat sink is also quite paying attention to, whether it is a wind-free radiator or a water-cooled radiator, it requires a suitable pressure to ensure that the radiator and the CPU have a tight contact, but must not vigorously have a miracle, and the loss of the main board is not small. .
Some CPU heat sinks are fixed on the motherboard by screws, while the attached screws are not fastened. Once the heat sink is too tight, the main board is oppressed, resulting in a deformation, resulting in irreversible damage. In addition, the weight of the radiator is relatively large. If the board does not screw all the screws, it will be greatly affected.
Use the heat sink installed with screws to screw all the screws during installation, do not tighten every one, and you should fix all the screws again, and feel that the large resistance is installed when tightening the screw. complete. After the installation, the heat sink does not shake or rotate, and the motherboard is not deformable and the basis for judging the reasonable installation of the heat sink.
For newcomers, you can choose to operate more simple heat sinks. This heat sink is fixed to the bottom plate with two buckles. Such a buckle does not allow the CPU to receive too much pressure while it can be better. The degree of control.
When installing a snap-on radiator, first hang one end without a metal wrench, then adjust the position of the radiator body, and press the metal wrench to hang this side. After installing the heat sink, gently twisted the radiator allows silicon to make the silicone fat, or better fit the CPU radiator to the base.
Finally, we still have to remind everyone that the installation and use of the radiator cannot be horses and tiger, choose the right heat sink is very necessary. Don't want to be of course when installing and replacing, the correct way of use can be more than half-time, and can upgrade in us later. I save a lot of trouble when maintaining.
Original link: https://www.eeboard.com/news/greease/
Search for the panel network, pay attention, daily update development board, intelligent hardware, open source hardware, activity and other information can make you master. Recommended attention!
[WeChat scanning picture can be directly paid]
Technology early know:
3 kinds of Great Visites Development Board Trends Professional - Talking about X86 Raspberry Panel Type UP Series
Haven't sold it yet, the company's valuation has exceeded 1 billion US dollars, this mobile phone is listening to the beauty.
The thunder's iPhone mobile phone, flicked directly in the trouser pocket
Beautiful research on minimum 3D printing microfluidic device, can print the chip is expected to achieve large-scale production
Mysterious manufacturer launches LCD screen, reloaded up to 480MHz creation high
Our other product:
