As a brand of only one year, iQOO has released the second 5G mobile phone - IQOO 3, which refers to the performance iron triangle combination. And announced the official game for KPL on the same day.
Ewisetech has also been released before sharing over the value. After the engineer analyzes it, take a look at how to go through the in-depth IQOO3 internal components.
First of all, first start from the configuration, come to find out this phone.
SOC: Qualcomm Snapdragon 865 processor, 7nm process
Screen: 6.44 inch 丨 Super AMOLED full screen 丨 resolution 2400x1080 丨 Screen 84.2%
Storage: 6GB RAM + 128GB ROM
Front: 16 million pixel camera
Rear: 48 million pixel main camera +13 million pixel wide angle camera +13 million pixel portrait camera +2 million vision depth camera
Battery: 4370mAh lithium ion polymer battery
Featured: Support 5G network 丨 side septic button
Be
Then disassemble it and make it easy to analyze.
Carto has a waterproof and dustproof effect with a silicone ring. The rear cover is fixed by the inner support, and the heat gun is heated to 190 ° C, the rear cover is heated and the inner support gap is slowly opened.
The rear camera cover is fixed by a rear camera. There is a foam fixation with the camera.
The motherboard cover and the speaker are fixed by screws, and the large-area graphite sheets are covered with heat dissipation in the battery and speaker position.
The flash soft plate and antenna soft plate are fixed by gel, and the handset module and the motherboard are connected to the front side of the motherboard cover.
The camera is a separate module, which posted a conductive tape protective effect on the soft board. The 13 megapixel portrait camera soft board is covered with a BTB cover for protection. The main board processor & memory position is applied with heat dissipation silicone and direct contact with heat dissipation copper tubes. A heat dissipation copper foil is used for heat dissipation.
Like the previous generation of iQOO PRO 5G, the motherboard uses a double-layer stack.
The battery is supported by the plastic tape and is attached to the tale handle to be removed.
Inside the support, the key soft plate with protective silica pads, the front fingerprint recognition sensor soft plate is protected by a cover, and the speaker is in the speaker outlet with a silicone ring for waterproof.
The liquid cold copper pipe extends from the motherboard to the battery position.
The screen is supported by the inner support. The heating table is heated, and the temperature is approximately 80 ° C, and the screen is separated from the inner support.
The information of the module is still separately.
The screen is a 6.44-inch 2400x1080 SUPER AMOLD full screen, the model is SAMSUNG AMS644UQ01.
Rear 48 million pixel main camera, model is Sony IMX582, the aperture is f / 1.79
Rear 13 megapixel portrait camera, model is Samsung S5K3L6, the aperture is f / 2.46
Rear 13 megapixel wide angle camera, model is Samsung S5K3L6, the aperture is f / 2.2
The rear 2,000-scented depth camera, the model is Geko microelectronics GC2375, the aperture is f / 2.4
The front 16 million pixel camera, the model is Samsung S5K3P9, the aperture is F / 2.45.
Then is the most important component analysis.
EWSETECH engineers found 1762 components in iQOO3.
Among them, Japan provided 1529 parts costs only 7.6%;
China provides 161 parts, accounting for 13.6% of total cost;
The United States provides 61 parts, cost proportion of cost is 47.3%;
South Korea provides 7 parts, accounting for 31% of total costs;
There are also 4 parts of other regions, accounting for 0.5% cost.
In view of the cost TOP5, you can understand why the number of components in the United States and South Korea is not much, but the cost is much higher.
The total cost is estimated to $ 305.88, which contains $ 3.8 assembly fee. The cost of the main control IC occupies a total cost of about 56%.
Of course, the most complete component information is still going to search for the ewistech search.
Specific IC distribution on the motherboard, of course, can not forget.
The main IC of the motherboard (below):
1: QUALCOMM-QDM2310-radio front end module chip
2: QUALCOMM-QM77040-radio front end module chip
3: Skyworks-sky78191-21-radio front end module chip
4: Samsung-kludG4UHDB-B2D1-128GB flash chip
5: Samsung- K3LK2K20BM-6GB memory chip
6: QUALCOMM-SM8250-Qualcomm Snapdragon 865 processor chip
7: QUALCOMM- XD55M-5G module chip
The main IC on the back of the motherboard (below):
1: QUALCOMM-PMX55-Power Management Chip
2: QUALCOMM-PM8150A-power management chip
3: QUALCOMM-PM8250-Power Management Chip
4: QUALCOMM-PM8150B-Power Management Chip
5: QUALCOMM-SDR865-radio frequency transceiver chip
The main IC of the small board (below):
1: QUALCOMM-QCA6391-WiFi / BT chip
2: NXP-SN100T-NFC control chip
3: QUALCOMM-QPM5677-RF power amplifier chip
4: QUALCOMM-QPM6585-RF power amplifier chip
5: QUALCOMM-QPM5679-RF power amplifier chip
Summarize
IQOO 3 motherboard uses a double-layer stacking method. The inside is heat dissipated by graphite sheet + heat dissipation silica fat + liquid cold copper tube. The liquid cold copper pipe extends from the motherboard to the battery position. And the main board and the battery position are laid with large graphite sheets for heat dissipation.
The whole machine is in the SIM calorker, and there is a silicone ring at the outlet of the speaker.
Although the LDS antenna should be the best option plan for manufacturers due to the accuracy and reliability of the antenna. But IQOO 3 is still using the FPC antenna and does not use the LDS antenna. (: JUDY)
PS: EWSETECH purchase machines are purchased through the official public channels of the market, and each product may have different suppliers, which is subject to the disassembled machine.
And the cost estimate of the metader is for reference only, and there is a certain difference with the real cost.
In the ewistech search, more iQOO devices are waiting for you ...
Iqoo - iQOO Pro 5G
Iqoo - iqoo neo
From ewistech.
Our other product:
