After reading the MX3 preliminary experience, we will leave hardware performance, system experience, and take a look at MX3 work. In my impression, the feeling of Meizu has always been very delicate, especially from the MX series model, exquisite in the system interface, and also exquisite in the design. In addition, it is still an alternative, the big screen phone is said, and the Meizu is not rushing to pursue a larger screen, and the MX3 is equipped with a 5.1-inch screen, and this alternative is also resolution.
Next, let's take a look at the internal workmanship of MX3, the machine metal frame is fine, and the screen technology has also reached the top level. Let's take a look at Meizu MX3 dismantling graphic evaluation.
First, the Meizu MX3 continues to cover the cover, the overall style is similar to the MX2, the overall thinner, the body size is slightly larger.
Many people complain that the back cover of MX2 opens some troubles, but in MX3, this is better, although it is still a spring card fixed, but it is fine-tuning, and it is more convenient to open.
After the rear cover is open, the battery is directly exposed, and it is not covered with a metal plate like MX2. Will such a design better? We also need further observation.
The middle frame portion uses a plastic material, reducing the weight of the whole machine, and a total of 11 cross-shaped screws on the fuselage need to be disassembled.
In addition to the protection of the protective effect, the flash and speaker units are integrated, while the flash is installed on the back cover when MX2, so that the cost of the user replaces the rear cover is reduced. In addition, there are several antennas of the antenna on the back cover.
Internal structure change
Relative to MX2, the internal structure of Meizu MX3 is relatively complex. It can be seen from the exposed cables, and the overall is also divided into four major parts, motherboards, batteries, small motherboards and LCD screens.
Remove the motherboard, components
First remove the parts on the plane, three cross screws of the motherboard, remove the headphone jack, open all the cables and a RF cable, the motherboard can be easily taken.
Motherboard, part list
The light sensor and the front camera are fixed to the front panel with the front panel, which is not designed to remove the handset, and the vibration unit can also be removed. The battery is still very headache, it is a strong glue, you need to pay attention to the motherboard connection cable below the battery when you are.
2400 mAh battery
A battery is not detachable when built-in 2400 mA.
Sony battery
From the back of the battery, we can also see the Meizu MX3 equipped with the Sony battery.
Unique vibration unit
The vibration unit of Meizu MX3 is characteristic, and the traditional vibration unit is a rotor, and the MX3 is equipped with two rotors. The vibration unit is fixed with three cross-shaped screws.
Double rotor vibration unit
There is a rotor in both the vibration units.
Front 2 megapixel back shot
The front 2 megapixel Sony backlight camera and fixed buckle. The front lens supports 1080p video shooting.
Inframe integrated flash
The flash unit and the camera opening on the box are opened.
Speaker unit
The speaker unit has four contacts around the speaker contacts and antenna contacts, respectively.
Button, headset, handset
Button, headphone interface and handset.
Small motherboard
The small motherboard is fixed with five cross-shaped screws and is connected to the motherboard with the cable and radio frequency cable.
Motherboard cable, main microphone, USB interface
The small motherboard integrates a connection cable, a main microphone, a USB interface, and the like.
HOME key sensing parts
The small motherboard is the HOME key induction device.
HOME button close-up
HOME key close-up. The HOME key is a touch button, not an entity.
RF cable
There are a total of two radio frequency connecting lines inside the fuselage, a long short. It can be seen that there is a metal frame on the liquid crystal panel to ensure the strength of the whole machine.
Light sensor and touch unit
The light sensor unit and the touch unit in the upper portion of the liquid crystal panel cannot be disassembled.
Light sensor close-up
Light sensor, touch chip.
Screen touch unit
Synaptics S3202A: Screen touch unit, many smartphones use the brand's touch chip.
Power switch, light sensing cable
Power switch, light induction cable.
Welding shield
Unfortunately, most of the chips of the motherboard are protected by the shield and cannot be easily removed. It is recommended that users do not try to dismantle.
Back cover card, metal border close-up
The rear cover, the metal border is close-up, and it can be seen that the solder joint is very exquisite, and the snap is also very secure.
Metal frame structure
The metal frame structure is provided on the liquid crystal panel to ensure the overall strength of the body.
Graphite cooling sticker
The next section enters the motherboard portion, the motherboard covers a large area of graphite cooling stickers, which also integrates the main camera, detachable. However, the shield under the sticker is soldered on the motherboard and cannot be removed normally.
Motherboard part chip
The back part of the motherboard is exposed to the outside, and you can see the CPU and memory part. The camera is connected to the motherboard with the cable.
Dismantle
The camera is removed.
8 million pixel back photo three generations Sony lens
8 megapixel Sony back in the main shot, F2.0 aperture.
Camera cable
The camera is closely written, and the back of the camera is fixed with the liquid crystal panel.
EXYNOS 5410 double four-core processor
Samsung Exynos 5410 double four-core processor, main frequency 1.6GHz. It consists of an A7 quad-core and an A15 quad-core, working together between low power and high performance, coordinates according to the running program, and it has built a PowerVR SGX 544MP graphics processing unit.
No clear chip
Volume button
Power management chip
MAX77665AEWQ: Power Management Chip
Dew part of the chip
Be
Microsim card slot
Meizu MX3 family portrait
Meizu MX3 - still fine, excellent workmanship
If I want to evaluate the internal structure of Meizu MX3, then I can say that MX3 is still very boutique, the internal excellent workmanship, beautiful design, completely exceeds many domestic, even international manufacturers, The refinement of Meizu mobile phones is not only reflected in the external form, but more, it is actually "distributed" inside.
Our other product:
