Remote switch
The remote control is one of the modern industries or modern families. It consists of a movable remote transmitter, and a switch receiver fixed to the wall. All functions can be directly operated on the wall switch or by remote control. Long-distance control.
Remote switch division transmission (remote control) and reception (switch) two parts, the transmitter encodes the control electrical signal, then modulate (infrared modulation, electromagnetic modulation, network data signal modulation), converted into a wireless signal to send out; Receive principle: To the wireless wave signal containing the information, then enlarge, decoded to obtain the original control electrical signal, and the electrical signal is again enlarged to drive the relevant electrical components (thyristor, relays and Moscou).
Remote switch principle
RFREMOTEMODULE is a remote control device that controls various agencies of remote signals using radio signals. These signals are received by the distant receiving device, and other corresponding mechanical or electronic devices can be instructing or driven to complete various operations, such as closed circuits, mobile handles, and start motors, and then needed to operate. As a type of remote control with the infrared remote control, a wide range of applications in garage doors, electric doors, trunks remote control, anti-theft alarms, industrial controls, and wireless intelligent homes.
Common remote control switch remote control systems generally distribute and receive two parts.
Transmitter is generally divided into two types, namely, remote control and transmitting modules.
ReceivingPart is generally divided into two types, namely, ultra-extra-difference and hyperbupler reception.
Common carrier frequency (carrierfrequency) is 315 MHz or 433 MHz.
Characteristics of remote control switch
1. Use wireless digital identification technology, each switch each independent address code, does not interfere with each other.
2, compatible with regular manual operation, wireless RF remote, no directionality.
3. According to the design, installation, wiring and ordinary mechanical wall switches are identical in accordance with international electrician practices.
4. Applicable to various types of qualified luminaires, household appliances, etc., no need to separate the peripheral device.
5. The switch and the remote control are used to use a smart bond to learn the code, which can add a remote control or a plurality of switches.
6, built-in abnormal protection function and user can change the fuse, with lightning protection functions.
7, embedded software, easy to modify, easy to update.
What is the advantage of using the remote control switch
1. The so-called remote switch, long distance or partition wall for wireless remote control is naturally the other switch can't match.
2, when the power supply light is turned off, the power supply is restored, the remote control switch will automatically be closed, and the general switch is not turned off in time, the light will remain in the open area, very waste of electricity.
3, lightning protection, lightning protection settings make the light remote control switch with more reliable safety performance, and the inside of its internal setting can protect the circuit in thunderstorm weather.
4, two-way control is a major feature of the remote control switch, that is, the two-way, which can switch the lamp using the remote switch, and when the remote switch is not around, the switch can be operated by the switch, which is quite convenient to use .
Lamp remote control switch wiring method
1. Disconnect the power, pull down the electric box.
2. Remove the original lightport wiring and remove the light port.
3. Power the power line of the original lamp to pick up the remote switch of the remote switch (generally red), the zero line of the supplier of the original lamp (generally black line).
4. Out the rocincid switch output the zero line (black line) to connect the outer screw column of the lamp mouth, and output the rocker switch output the fire line (generally a blue line) to connect the inner center of the lamp. The receiving antenna of the rocker switch (generally white line) is disconnected.
5. Confirm that all the wiring is correct, and the insulating tape can be supplied.
Intelligent lighting light remote control switch wiring method
1) Generally, when the bedroom wiring is installed, there is a power outlet near the switch box, and the smart light remote control switch is loaded into the switch cartridge. The two power cords of the fire line and the neutral line are attached from the nearby power socket, respectively, respectively, respectively. Remove the three lines on the original switch, change the remote switch K1 / K / K2 of the intelligent lighting light, pay attention to the three terminals of the original switch; if the bed switch box is not easy to receive, the bedroom door switch box It is easy to receive the power supply, and the smart lighting light remote control switch can be placed in the door switch box, and the wiring must not change; if there is no power supply nearby, it can be considered from the lighting lamp, and wear a line along the original line of the bed. Inside the switch box, the zero line at the light is connected, and then the above-described method connection can be installed.
2) Single fire intelligent lighting light remote control switch is installed, standard 86 wall switch, no need to pick up the line, do not need to change the lamp, can replace the original wall switch (suitable for picking up the sunlight, energy saving lamp, incandescent lamp, shot Frequent lamps such as lamps, halogen lamps);
3) Flower smart light light remote control switch installation does not need to be rewired, do not need to change any accessories for lamps; choose the load group required to use, press the anti-theft key for 5 seconds, the selected light group will flash twice After the delay is 60 seconds, the selected light group is extinguished. At this time, the lamp has entered the anti-theft work status; two-way control, mutual disturbance!
Lamps Lighting Remote Switch Installation Process
First of all, we should first know what is the lighting remote control switch, and the classification of lighting remote control, such as single-controlled wiring mode, single single control is a switch to control all the way lighting, even if it is used to control lighting, I usually Make a wall switch panel to prevent future remote control circuits fail, or when the battery is dead, you can control the circuit lighting with a wall switch. Single single control remote control I feel particularly suitable for the lights of the hall. Because such a remote control is like a key pendant, it is very small, you can hang on the key chain, when you go home, you can open the door outside the door, you can open the door of the house in the door.
Secondly, the single multi-control wiring mode is known. The single multi-control is a switch control multi-channel lighting. I didn't expect this control method. I started to buy a single controller for the former hood. I haven't figured it out, wait for me to understand, the panel has been installed, the panel is used to control three lighting lines with three panels, so the single-controlled remote control is a line. Come over, there is only one switch in the wall panel, but the remote control can control multiple lighting.
The third is a multi-channel multi-control, which is combined with multiple single-controlled lighting circuits. All lines, give the front home dress, one master, four bucket lights, there is a light strip The line is controlled by three wall panel switches. The remote control is also controlled by three keys. Although this approach is more tip, I think that the various tubes seem to be insured.
When installing the lamp remote control switch, we should first look at the circuit diagram of the remote control, remember that the general light-control switching device zero fire line cannot be reversed, and many construction teams are subjected to zero lines, and they are not divided into zero fire lines for the lights. Jelly. In fact, although this light is only two lines, it is also divided into the rib line. The fire line is an entry, the zero line is outline, and the zero fire line will be taken when loading this remote control, don't get wrong. This remote control receiving device is directly sticky in the lamp with a non-adhesive. This does not stick to the lamp. In fact, the temperature is high after opening, if this may be used for a while, this non-adhesive will fall off. Later, the brother has taken two eyes with a drill, and the remote control is given to the lamp, so it is true.
Lamp remote control device installation consideration
1. Remote circuit installation should pay attention to the zero-fire line, and the multi-channel receiving device switch is connected to the light line of the illumination.
2. This remote lighting circuit is very convenient, especially suitable distance from the two-control two-control, two-control, two-to-rise.
3. A multi-channel multi-control remote control with the receiving device has an oxide, and the single-handed single-controlled code is not used.
Our other product:
