FMUSER Wirless Transmit Video And Audio More Easier !

[email protected] WhatsApp +8618078869184
Language

    General knowledge about science first use of motor

     

    1. Check before the motor installation 1.1 Motor mounting size and basic parameters check. 1.1.1 Universal Motors can be checked according to motor samples. Special motors or technical protocols, the motor of the outer graph must be inspected according to the agreement requirements and proofreading, and the results can be performed after the results can be performed. 1.1.2 The motor nameplate is consistent with the contract or agreement. 1.1.3 Turn in the direction of rotation. Low-pressure general product (H80 - h315) does not rotate requirements, the motor can be positive and inversely operated; low voltage high power products must look at whether the motor direction indicator and contract or agreement are consistent. The high pressure 2,4 pole motor rotation is required, and the 6-pole motor has no rotation requirements (except special circumstances). The direction of rotation must consistent with the direction of the main unit to act normally, otherwise the motor is highly tempered by the motor. 1.2 Motor check. 1.2.1 DC resistance check Motor three-phase winding DC resistance check: Measure the DC resistance of the three-phase windings, the difference between the three-phase DC electrical resistance of one phase and the average value of the three-phase winding DC resistance is larger than the average value of the three-phase winding DC resistance. 1% . 1.2.2 insulation resistance check Insulation resistors Check the insulation resistance of the winding on the ground. The insulation resistance of the stator windings was measured using a shaker having a output voltage between 500 to 2500 volts DC voltage. If the measured value is ≤ 1 MΩ / kV, the winding is to be drying. 2, basic examination 2.1 The foundation should have sufficient strength to avoid resonance of the system and the power generated in normal and abnormal operating conditions. 2.2 Basics should be able to withstand sudden mechanical moments in the motor start or in abnormal conditions. 2.3 Basis or steel foundation should allow about 2 mm liner. However, it should not exceed 4 mm under any circumstances. 3, find a status request 3.1 When the motor is installed, the motor shaft center line must be consistent with the centerline of the drive machine, otherwise the bearing damage and the shaft break, the tolerance between the two couplings meets the standard. Pay special attention to protect the bottom foot plane of the motor, do not have bumps, damage. When adjusting the motor center, the flat pad should be increased between the bottom plane and the rigid foundation of the motor, and the number of pads should be as small as possible. 3.2 When you find a time, you should ensure that the axial gap is sufficient while considering the amount of thermal expansion of the motor. 4, test machine 4.1 Empty test machine: First test machine, point to the motor, check the motor. The rotation is energized correctly. The initial operation is detected every 10 minutes to detect the vibration of the motor, the bearing temperature, after 30 minutes, can extend the detection time interval, and detect once for 30 minutes. Run 2 hours, no problem can stop the test machine. 4.2 Full load test machine: Full load test machine items. Just running time to reach more than 4 hours. EDTOR: JQ, read full article, original title: General knowledge of motor initial use Article Source: [Micro Signal: Wwygzxcpj, WeChat public number: motor technology and application] Welcome to add attention! Please indicate the source of the article.

     

     

     

     

    List all Question

    Nickname

    Email

    Questions

    Our other product:

    Professional FM Radio Station Equipment Package

     



     

    Hotel IPTV Solution

     


      Enter email  to get a surprise

      fmuser.org

      es.fmuser.org
      it.fmuser.org
      fr.fmuser.org
      de.fmuser.org
      af.fmuser.org ->Afrikaans
      sq.fmuser.org ->Albanian
      ar.fmuser.org ->Arabic
      hy.fmuser.org ->Armenian
      az.fmuser.org ->Azerbaijani
      eu.fmuser.org ->Basque
      be.fmuser.org ->Belarusian
      bg.fmuser.org ->Bulgarian
      ca.fmuser.org ->Catalan
      zh-CN.fmuser.org ->Chinese (Simplified)
      zh-TW.fmuser.org ->Chinese (Traditional)
      hr.fmuser.org ->Croatian
      cs.fmuser.org ->Czech
      da.fmuser.org ->Danish
      nl.fmuser.org ->Dutch
      et.fmuser.org ->Estonian
      tl.fmuser.org ->Filipino
      fi.fmuser.org ->Finnish
      fr.fmuser.org ->French
      gl.fmuser.org ->Galician
      ka.fmuser.org ->Georgian
      de.fmuser.org ->German
      el.fmuser.org ->Greek
      ht.fmuser.org ->Haitian Creole
      iw.fmuser.org ->Hebrew
      hi.fmuser.org ->Hindi
      hu.fmuser.org ->Hungarian
      is.fmuser.org ->Icelandic
      id.fmuser.org ->Indonesian
      ga.fmuser.org ->Irish
      it.fmuser.org ->Italian
      ja.fmuser.org ->Japanese
      ko.fmuser.org ->Korean
      lv.fmuser.org ->Latvian
      lt.fmuser.org ->Lithuanian
      mk.fmuser.org ->Macedonian
      ms.fmuser.org ->Malay
      mt.fmuser.org ->Maltese
      no.fmuser.org ->Norwegian
      fa.fmuser.org ->Persian
      pl.fmuser.org ->Polish
      pt.fmuser.org ->Portuguese
      ro.fmuser.org ->Romanian
      ru.fmuser.org ->Russian
      sr.fmuser.org ->Serbian
      sk.fmuser.org ->Slovak
      sl.fmuser.org ->Slovenian
      es.fmuser.org ->Spanish
      sw.fmuser.org ->Swahili
      sv.fmuser.org ->Swedish
      th.fmuser.org ->Thai
      tr.fmuser.org ->Turkish
      uk.fmuser.org ->Ukrainian
      ur.fmuser.org ->Urdu
      vi.fmuser.org ->Vietnamese
      cy.fmuser.org ->Welsh
      yi.fmuser.org ->Yiddish

       
  •  

    FMUSER Wirless Transmit Video And Audio More Easier !

  • Contact

    Address:
    No.305 Room HuiLan Building No.273 Huanpu Road Guangzhou China 510620

    E-mail:
    [email protected]

    Tel / WhatApps:
    +8618078869184

  • Categories

  • Newsletter

    FIRST OR FULL NAME

    E-mail

  • paypal solution  Western UnionBank OF China
    E-mail:[email protected]   WhatsApp:+8618078869184   Skype:sky198710021 Chat with me
    Copyright 2006-2020 Powered By www.fmuser.org

    Contact Us