September 6th, glory V9 Play released, high-quality appearance, up to 4GB of memory, and high cost performance becomes the highlight of this phone. So as the low-end version of the V9 series, is its internal workmanship? Let us look at its work through dismantling!
Glory V9 Play Screen resolution is only 720p, but the screen color is very bright. The 5.2-inch size of the other machine has better handling. The front of the fuselage is designed without an entity buttons. The front head of the fuselage and the colors of the chin are unified with the back shell, the same is dark blue. The top is designed with earpiece front and light distance sensors.
The bottom of the fuselage has two hexagonal anti-demolition screws, the middle is the data interface, the headset is designed in the top of the body.
Shut down the SIM card slot, the machine uses or the card slot.
First use the hexagonal screw knife to remove the two screws at the bottom of the fuselage.
Subsequently, the back shell is pulled up from the bottom of the body from the bottom of the body, and the slit separation buckle is expanded to the edge. The back shell can then be opened, but be careful that the fingerprint cable is also connected to the back shell, which is easy to tear.
After opening the back shell, you can see the inside of the knife body, the connector is good, did not see the bare connector, including the same axis. Let's take a look at the back shell, and the fingerprint recognition module is attached to graphite tipping auxiliary heat dissipation. What we first need to do is to disconnect the power and disconnect the fingerprint recognition connector to separate the back shell.
After separating the power connector, the fingerprint recognition cable begins, and then remove the cover screw first. Separate the cover, the bottom is the fingerprint cable connector and the screen display cable.
In the SIM card slot position, we see a sealed bubble, it can be seen that the machine has certain requirements.
We also saw the rubber seal in the headset interface.
The data interface and the microphone interface at the bottom of the fuselage also saw the sealed rubber. It can be inferred that the survival rate of rapid removal of the rapid removal in a short time is soaked.
Let's take a look at the circuit design of the motherboard. Almost all bare capacitors, other chips are designed in the metal shield. In terms of spatial utilization, the intermediate area is to leave space to the fingerprint recognition module, and some have a horizon area, but not much.
The back core element of the motherboard is exposed, but everyone will not be surprised, you will know the answer later. We see that there are three large chips to have heat-conducting silica gel, and it is still very good. A large portion of the top is idle is used by the drum.
The answer was announced, and we see that the chip corresponding to the rolls under the motherboard is designed with a spacing to play a shield. Although this is designed and there is no shielding effect, it is also possible to save costs.
The machine camera is 1300W back, 1.12 micron pixel area supports PDAF focus; front camera 800W pixels.
After the first graphite radiator on the back of the motherboard opened, the processor Union MT6750 was used to use 8 core A53 architecture, and the Mali T860 displays the core. Two heat dissipation silica were left separately, and the 32GB flash memory of Sni Di and the 4GB memory chip of Hissanti were seen.
The shield of the front surface of the motherboard is opened, and the thermal silica gel is also seen in the corresponding position of the power management chip.
Overall, the glory V9Play motherboard is high, and if the performance of the same model is very good.
But you can also see some traces of cost savings.
RF chip close-up
Removing the speaker module is also designed with a vibration module on the back of the speaker, and the contact is connected to the sub-board.
The machine battery is rated by 2900mAh, 11.08Wh.
Dismantle the whole family
After removing us, we can see that the glory V9Play has a good seal, the chip shielding, heat dissipation design, the fixture's fixation, and the main board component density is in place, the big factory battery is also safe, but it can also see it Many traces of cost savings, such as the corners do not do, buttons, and some connector use low cost components, but in general, the workmanship of this machine has been calculated in the same model model. If you consider buying this machine, as long as the price is appropriate, accept the configuration, you can start.
Our other product:
