Proteus8.9 Simulation STM32407ZGT6 Series 001_走 马

First, open the template file (can be downloaded with the text placed in the document is opened). (As shown in FIG. 1) FIG. 1 II click Source Code tab. (As shown in FIG. 3) in FIG. 2 FIG. 3 III, right click, add new files led.cled.h. (As shown in FIG. 4) FIG. 4 IV, save the project file, edit main.cled.c led.h code. (As shown in FIG. 5) FIG. 5 five, Main.c Code: #include "stm32f4xx_conf.h" #include "sys.h" #include "delay.h" #include "usart.h" #include "led.h "u8 t = 0, str [] =" Angela loves baby .. \ n "; int main (void) {NVIC_PriorityGroupConfig (NVIC_PriorityGroup_2); // set the system interrupt priority packets 2 delay_init (168); // initialize delay function uart_init (9600); // initialize serial LED_Init (); // initialize LED port if (USART_RX_STA & 0x8000) while (1) {LED0 = 1; // first illumination lamp LED0 delay_ms (500); LED0 = 0; LED1 = 1; // first illumination lamp LED1 delay_ms (500); LED1 = 0; LED2 = 1; // first illumination lamp LED2 delay_ms (500); LED2 = 0;}} Led.c Code: #include "led. h "void LED_Init (void) {GPIO_InitTypeDef GPIO_InitStructure; RCC_AHB1PeriphClockCmd (RCC_AHB1Periph_GPIOC, eNABLE); // enable GPIOF clock // GPIOF9, F10 initialization setting GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3; // LED corresponding to the pin GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT; // normal output mode GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; // push-pull output GPIO_InitStructure.GPIO_Speed ​​= GPIO_Speed_100MHz; // 100MHz GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; // pull GPIO_Init (GPIOC, & GPIO_InitStructure); // initialize} Led .h Code: #ifndef __LED_H # define __LED_H # include "sys.h" // LED port definition #define LED0 PCout (1) #define LED1 PCout (2) #define LED2 PCout (3) void LED_Init (void); // initialize #endif six clicks to build the project button to compile the project. (Shown below in FIG. 6) FIG. 6 seven, the bottom left click simulation button, visible red, yellow, green 0.5s each jump flash emulation. (As shown in Figure 7,8,9) 7 8 9 Eight, select release, click on the button to build the project, compile the project Hex File. (As shown in FIG. 10) in FIG. 10 IX I is prepared in F407ZGT6 core plate P, P are automatically downloaded by the download software Proteus VSM Studio Hex file generated to the development board. Visible red, yellow, green development board module each red, yellow, green jump flash 0.5s. (As shown in FIG. 12, 13) in FIG. 13. FIG. 11 FIG. 12 Annex Proteus8.9 series based simulation STM32407ZGT6 template t00 to open Proteus8.9 installed in a computer folder. Need further information, please join the QQ group: 976 235 464, Read more

Our other product:

Professional lightning protection system for Tower	Professional FM Radio Station Equipment Package	FMUSER FU-1000C 1000W FM Transmitter With USB Audio Input Interface
FMUSER 200W FM Radio Broadcasting Package	Hotel IPTV Solution	FMUSER FSN-1000T V5.0 1KW FM Radio Broadcast Transmitter