When 5G just appeared, the small E home has included the information of the Samsung Galaxy S10 5G version of the Korean version. This time, Note 10+ 5G was officially released in China, and Xiao E naturally won't let it. Detailed data is naturally a time finishing. So until now, the detailed data is finished. Little E Rapida collected information from engineer's little brother to share.
Configuration list
SOC: Qualcomm Snapdragon 855 Plus 丨 7nm LPP Process
Screen: 6.8 inch Samsung Dynamic AMOLLE screen 丨 resolution 3040x1440 丨 Screen accounts for 91.2%
Storage: 12GB RAM + 256 ROM, up to 1TB extension
Front: 10MP
Back: 12MP wide-angle main photo + 12MP telephoto + 16MP super wide angle + 2MP 3D depth of field camera
Battery: 4170mAh lithium-ion battery
Features: Ultrasonic fingerprint recognition | Reverse wireless charging | IP68 dustproof waterproof | Intelligent variable aperture | water carbon cooling system | screen pre-camera | s Pen empty operation
Dismantlement step
First take the S Pen and the SIM Card Toro with a film, S Pen built-in action sensor, click the S Pen button to implement the phone.
Note10 + 5g is a glass rear cover, the rear cover is strong, and the heating temperature reaches nearly 200 °, and the rubber is melted, and then the rear cover can be drawn from the tile. The rear camera glass cover is still posted with a pressure balance film. There is also a hole with a waterproof silicone sleeve, which is used for noise reduction microphones.
The pressure balance film, Samsung's flagship machine model is basically used, which reduces the stress to be subjected to the phone through balanced mobile phone inside and from outside the phone, and protecting the internal components from the liquid used in daily life.
Through the adhesive NFC / MST / wireless charging coil, it can be removed, and the main board and the canapper soft plate are also fixed. BTB metal cover, top and bottom antennas are fixed by screws.
The rear camera is fixed by two screws. Remove the motherboard, panel, two main panels to connect the soft board. After the front and rear camera soft board and the antenna plate, it is found that there is a piece of empty groove on the inner support, which may be used for mobile phone antenna design of different countries.
The motherboard has a higher cost of double-layer board, and the two motherboard spacing is 0.9mm.
The antenna plate is supported by the screws.
The handset, vibrator, white S Pen cover, buttons soft plates and coil soft boards are fixed. The vibrator is changed to a new square vibrator and tactile feedback is better. The power button and the Bixby key function are integrated together, and it also saves internal space.
The handset is located under the front camera, and the sound is conducted to the top grille through the metal sheet on the back, and functions.
The coil soft plate is fixed to the S Pen cover by rubber, and the coil soft plate and the coil in the S PEN are induced to charge the S Pen.
The heat conductive copper tube and the battery are fixed through the glue. The copper pipe is composed of "water + electric carbon fiber" with better thermal conductivity.
Finally, the screen and internal support are separated by heating. The ones of the left and right sides are thinner, only 1.6 mm, the thinnest place, the fixed button is 3 mm. The fingerprint recognition module is integrated on the screen, and the ultrasonic fingerprint identification module of Qualcomm is selected.
Module information
The screen uses the Dynamic AMOLED screen of Samsung 6.8-inch 3040x1440 resolution.
Front 10 MP camera supports autofocus function.
Rear 12MP telephoto + 12MP wide-angle main photo + 16MP super wide angle + 3D Depth camera, 12 MP telephoto and 12MP wide-angle mainly support OIS anti-shake, and mainly support F1.5 / F2.4 intelligent variable aperture.
The battery capacity is 4170mAh, and the battery cell manufacturer is chemical, which is relatively few in Samsung mobile phones.
S-Pen's appearance does not look at you, you have to show you the overall structure. As we all know, this year's S-Pen has added some functions than in previous years. In the structure, it is because a single action sensor is added.
The predivation cost of all parts above is $ 156.64. The total cost of the total cost is about 33.9%.
Motherboard IC information
Motherboard 1 The main IC (below):
1. QUALCOMM - Qualcomm Snapdragon 855 PLUS 8 Nuclear Processor
2. SAMSUNG-12GB memory chip
3. SAMSUNG-256GB flash chip
4. QUALCOMM -5G baseband chip
5. QUALCOMM - RF transceiver
6. Cirrus Logic - Audio Amplifier
7. NXP-NFC control chip
8. Goertek-Microphone
9. STMicroelectronics - Pneumometer
10. AMS-TMD4907-Light / Distance Sensors
Main board 1 main IC (below):
1. MURATA -WIFI / BT chip
2. QUALCOMM-audio decoding chip
3. 4 high-pass power management chips
4. 3 Samsung Power Management Chip
5. Goertek-Microphone
6. AMS - light sensor
7. STMicroelectronics - Gyroscope + Accelerometer
8. AKM - electronic compass
Main board 2 main IC (below):
QUALCOMM-RF transceiver
2. IDT-wireless charging transceiver chip
3. Wacom-s PEN Control Slices
Logic, Memory, PM, RF and AUDIO chip information used on the motherboard are shown in the table:
The MEMS chip information used on the whole machine is shown in the table below:
The cost price of these chips listed above is expected to be at $ 218.43, accounting for 47.2% of the total cost.
Summary information
Most of the whole machine is used in modules and chips. It takes about 81.1%. The subtleties are quite rigorous. Due to the compact structure, the motherboard uses a double-layer board design, canceling the headphone hole, the side bond is integrated into a soft board, the ultrasonic fingerprint identification module is integrated on the back of the screen, which is smaller than the other fingerprints, and effectively saves internal space. Due to the waterproofability of the whole machine, waterproof treatment is passed through the various openings and gaps.
Our other product:
