Today, I went to the game, I didn't stand my hand, I bought a cool supreme gold silicone. After coming back, I saw the thin summer vacation Xiaoxiao, so itchy itchy dismissed it (though Before this machine, there was a big god, but some pictures of sending were still somewhat intermittent, and several issues I encountered in the initial disassembly were that they would start in the article. . . . . . .
The first is the tool for the egg, there is no professional tool in your hand, just take the screwdriver of such a repair glasses to solve the Xiaoxiao to the cruel limb (because the tool is too small, some screws are big, no way, have to bite with the door The screwdriver turned, it is recommended that everyone will prepare for the tools, otherwise there is a danger of breaking the incisions)
In addition, today's protagonist: Cool is cold, gold silicone,, 呜呜, bought distressed
There is also a preparation, although it is simple, it is practical, and the transparent adhesive is placed on the desktop, and then the screw is sequentially stained in the order on the back sheet, which is not easy to lose the screw, which is relatively easy ( Although 46F is good, the screw is too much, there is a big small and small, and if you don't pay attention, you will miss one)
When all the screws unloaded, the rear of the optical drive was also removed, so that the panel behind it was better. At this time, the steel is not thrown, inserts the crack between the rear panels, slowly sliding slowly. After the first corner, there will be two dark cards, but after the two snaps are opened, the disassembly work is easy to do. Then, the entire panel is pulled to the right, the panel and the VGA interface are separated, and the rear panel is easily unloaded. The panel is to be detached as a whole.
The overall trace is still very clear, but the work and materials, everyone knows the same thing, I will not say more. . .
Next, the heat dissipation copper pipe is removed. . . Let us look at the toner of the pothole. .
The silicone color of the pothole is not correct, but it is not clear why one of the chips is a heat dissipation pad.
Next, clean the old silicone (the effect of hard toothbrush is definitely more clean than the hard hair brush, see the results I have cleaned.
Smooth is like a mirror
Next, I said that a method that everyone has never used: First, the silicone extrusion is 0.2-0.3cm (that is, there is a little silicone on the needle), then use the needle tube in the CPU (Graphics card) "point" on the silicone, there are many times here, and finally slowly cover the chip. At this time, the silicone is only to be said, but it is not a "thin" layer. Next, a flat heat sink is pressed, and then the silicone on the heat sink is removed, and finally the heat dissipation copper pipe is covered up OK. (See the effect map after I squeeze, it is definitely "thin" layer)
This is the advantage of the above silicone, the amount of silicone is very small (at least, my remaining silicone I will use 3, 4 times) silicone does not have too much to run to the chip (if you point There are too many silicon stains, then press it once, remember to remove the silica fat on the heat dissipation plate)
Finally, cover the braided copper tube, twist the screw, remember to connect the cable on the motherboard, and finally close the back panel, press the position and order on the transparent tape, tighten, big work (but on the back panel When it is recommended to use a screwdriver to pick up the HDMI interface, after inserting the interface into the hole on the panel, one of the slap in the back panel is closed.
Datual! ! !
Attach some views during the disassembly:
The last thing of the post spits:
1: Iron Man is deformed as a notebook in selling points, is actually a thing:
2: In order not to let the people enjoy the fun of DIY, the same party puts a screw on a screw on the rear panel (with a shaving blade, lightly, no loss)
3: The sound of the garbage is not to see any brand, the work is extremely poor, the wire is extremely hard, the effect is not mentioned (the sound is sticky with that industrial yellow gum, then the screw is fixed on the back panel)
For comrades who want to change the sound, I can only say that you can't buy so small, the effect is good, so let's die.
Even family portrait:
Our other product:
