When Vivo Z6 was released, it was once called a 5G mobile phone. That is 5G mobile phones, why can this Z6 selling so much? What measures have there have been controlled costs? Today, Xiao E takes you to analyze it.
Configuration list
The basic information sheet still has to look at, although Z6 is still added to the liquid cold copper pipe, the battery has also added 44W fast charge. Its screen selection is a TFT screen, and the fingerprint recognition also selects the back fingerprint recognition.
After we open it, let's take a look at what controls the cost.
Dismantlement step
Remove the SIM Carto first. The rear cover needs to use the hot air gun to heat around, with a suction cup and crowbar and other tools to remove the rear cover. Since the fingerprint recognition is connected and fixed on the motherboard, the rear cover must be careful, do not pull the cable.
The fingerprint identification of the back cover and the camera protection cover are fixed by gum, and you can take care of the crowbar.
The metal cover of the fingerprint sensor interface is fixed to the motherboard through the screw, and there is a fixed buckle between the frame and the inner support. There is a screw sticks with Vivo's defense. There is a protective bubble cotton at the interface, and the upper microphone is equipped with a silica gel case.
The antenna is fixed inside in the middle frame, which is an FPC soft board. There is no LDS antenna selected by many mobile phones when using it. This is also very good to control the cost.
The motherboard cover and speaker modules are fixed by screws with internal support. The motherboard cover is attached to a large area of graphite tiles. The vibrators and the sound position of the speakers are posted on the sound position.
The motherboard is shielded on the top of the copper foil for heat dissipation. The flashlight is connected to the motherboard through the contact between the handset and the motherboard, and the flash is connected to the motherboard shrapnel by contact.
The side of the battery has a tale handle for easy removal of the battery. In addition to the middle frame of the battery, there is a heat dissipation copper pipe in addition to the two connecting lines. The coaxial lines on both sides are fixed by black tape.
16MP front camera and 8MP + 48MP + 2MP + 2MP after photo.
The motherboard is fixed by screws, and the sub-plate is only secured by a snap, and there is a waterproof label on both boards. The front side of the motherboard has a heat dissipation copper foil. The main IC position is also coated with heat-conductive silicone, and the connection soft plate of the key plate and the main panel is fixed by double-sided adhesive.
The screen and the inner support are fixed, and it is necessary to separate by heating, with more glue and foam fixation in the front camera position.
6.57-inch LCD screen, resolution is 2400x1080, and select Tianma's display, so it is very good to control the overall price.
Motherboard IC information
The main IC of the motherboard (below):
1: QUALCOMM-SM7250-Snapdragon 765G Barn Processor
2: Samsung-KM2V8001CM-B707-6GB memory + 128GB flash memory
3: QUALCOMM-QPM **** - RF power amplifier module
4: QUALCOMM-QPM **** - RF power amplifier module
5: QUALCOMM-QET **** - Envelope Tracker
6: QUALCOMM-QET **** - Envelope Tracker
7: QUALCOMM-WCN **** - WiFi, Bluetooth, GPS
8: QUALCOMM-WCD **** - Audio chip
The main IC on the back of the motherboard (below):
1: qorvo-qm ***** - RF front block module
2: QUALCOMM-SDR *** - RF transceiver
3: qorvo-qm ***** - RF front block module
4: QUALCOMM-PM **** B-Power Management
5: QUALCOMM -PM **** A-Power Management
6: QUALCOMM - PM **** - Power Management
The MEMS chip information used on the whole machine is shown in the table below:
Summary information
Vivo Z6 still wants to be in terms of detail. The whole machine uses 20 screws and has a tag label. Waterproof labels are posted on the main sub-board. And a large number of graphite sheets and metal copper foils are used in the motherboard for heat dissipation, and the main plate CPU part is coated with a thermally conductive silicone, and the copper tube is used for heat dissipation. Use with foam and silicone clams at each interface.
But it is distributed around the FPC antenna around the box, and the cost is controlled on the selection of the module. It includes a processor using Qualcomm Snapdragon 765G. These are all effectively controlled costs. (: JUDY)
There are still many new 5G mobile phones that have also been entered in the ewistech sector.
Huawei - P40
Vivo - X30 5G
Reprinted from ewistech.
Our other product:
