Is there a small e-component cost analysis of iQOO? Little e told everyone today that this iQOO PRO 5G dismantling, there is a specific IC information table and price list, remember to look down.
Configuration list
SOC: Equipped with Snapdragon 855 PLUS processor 7nm LPP process
Screen: 6.41 inch Super AMOLED screen 丨 resolution 2340x1080 丨 screen occupies 83.7%
Storage: 8GB RAM + 128GB ROM
Front: 12MP camera
Rear: 13MP wide angle camera + 48MP main photo + 2MP side camera
Battery: 4410mAH lithium polymer battery
Features: Screen fingerprint | standalone AI button | Heat hot copper tube cooling | game pressure button | Back cover LED light strip
Dismantlement step
The glass rear cover is fixed by a foam, and it can be seen after the LED light plate BTB interface is fixed by the metal cover and screw. The SIM card is used by the spring fixed SIM tray using the upper and lower stacked design, and the SIM card can be placed on both sides so that the design can effectively save internal space. Tato has a silicone ring on a silicone ring, which plays a certain dust-proof waterproof.
The middle of the rear cover is a light guiding belt. There are two LED lamps on the lower ends of the light guiding tape, and the luminescence effect of the rear cover is achieved by the light guiding belt and the LED lamp. The rear camera protective cover is fixed by the adhesive, or it can be removed.
The main sheet and speaker module, the main plate cover, the speaker module, and the battery are removed from the front area. On the main board, the corresponding motherboard BTB interface is also posted, and the NFC coil is fixed to the main board by gum, and the vibrator is fixed to the speaker module.
The main sub-board connection cable 1 is disconnected to remove, and the battery is secured by easy disassembly. Since the use is 44W fast charge, the battery is achieved by two cables, and the motherboard and the secondary board are connected.
The motherboard, the secondary plate, and the ship plate are fixed by screws, and the main panel connection cable 2 is fixed by the glue. The rear camera, front camera and headphones hole soft board These can be taken together with the components connected to the motherboard through the BTB interface.
The motherboard is designed with a double sheet, and there is 4.7mm thick. The thickness of the two plates is 0.6 mm and 0.5 mm, respectively. The pitch between the two plates is 1.2mm.
BTB interface on the motherboard is protected by foam protection, and the devices on the motherboard have been treated.
Since the SIM card slot is the upper and lower stacked design, the thickness reaches 2.7mm, and the USB TYPE-C interface uses silicone ring waterproof.
Remove the side bonds with waterproof rubber circles, as well as side key soft board, AI key soft plate, fingerprint identification module, and handset. A vibrator support is found at the bottom, which is separated by the vibrator and the fingerprint identification module to avoid the vibrator to affect the fingerprint identification module.
The fingerprint recognition module uses a sensor similar to the camera module, using a fingerprint recognition scheme of the project.
Two game pressure button soft plates are connected to the main board by contacts.
Finally, the screen and internal support are separated by heating, and the inner supporting graphite sheet is supported. There is a heat conductive copper tube under the graphite sheet, which requires tearing the graphite to remove the copper tube.
Module information
The screen uses a 6.41-inch 2340x1080 resolution Super AMOLED screen.
Front Samsung 12MP camera, model is S5K2LQ, F2.0 aperture.
Be
From near to far, a 2MP sub-camera (F2.4 aperture, model GC2375) + 48MP main camera (model IMX582, F1.79 aperture) + 13MP wide-angle camera (model is S5K3L6, F2.2 aperture).
The battery is 4410mAH lithium polymer batteries, and the battery cell manufacturer is ATL.
Motherboard IC information
Motherboard 1 The main IC (below):
1. QUALCOMM-SM8150 - Qualcomm Snapdragon 855 PLUS 8 Nuclear Processor
2. Samsung-K3YH7H70AM-AGCL- 8GB memory chip
3. Samsung-kludG4UHDB-B2D1-128GB flash chip
4. QUALCOMM-SDX50M-5G baseband chip
5. QUALCOMM-PM8150B-Power Management Chip
6. AKM-AK4377A-HIFI chip
7. CHIPSEA-CSA37F61-Pressure Touch Chip
8. QUALCOMM-WCN3998-WiFi / BT chip
9. Light sensor
10. Distance sensor
11. AKM-AK09918C-Electronic compass
Main board 1 main IC (below):
1. 4 Qualcomm-power management chips
2. QUALCOMM-SDR8150-radio frequency transceiver
3. Goertek-microphone
The motherboard 2 is a single-panel, the main IC on the back (below):
QUALCOMM-WCD9340-audio decoder
2. AWINIC-AW22127-breathing lamp drive chip
3. STMicroelectronics-LSM6DSM-Gyroscope + Accelerometer
4. NXP-NFC control chip
5. QUALCOMM-SDR8154-radio frequency transceiver
The cost of the main functional chip on the motherboard is shown in the following table:
The proportion of the main devices in IQOO PRO 5G of $ 325.03:
Of course, this is just part of the cost. If you want to know more comprehensive cost information, you must poke into the ewistech search to learn more, more exciting information.
Summary information
Obviously, most of the money in the whole machine flowers on major chips and devices. However, the dust-free silicone ring inside the phone; protects the bare components and modules of the foam or point glue; the design of the double-layer motherboard and the double-layer card slot; the heat-dissipating heat-conducting copper tube, also confirmed that this phone did not Ignore the part of these details. This is indeed a cost-effective 5G mobile phone.
Source: ewistech
Our other product:
