Glory 20 is equipped with the current Huawei's best processor unicorn 980, and has been well received by many consumers since the sale. Small E will bring in-depth disassembly and component analysis, understand the metader information of glory 20!
Configuration list
First of all, let's take a look at the foundation configuration information. If the configuration information, it feels that it is a powerful player!
SOC: Kirin 980 Eight Nuclear Processor 丨 7nm Process
Screen: 6.26-inch TFT screen 丨 resolution 2340x1080 丨 Screen 84.6%
Storage: 8GB RAM + 128GB ROM
Front: 32 million pixels
Rear: 48 million pixels +16 million pixels +2 million pixels +2 million pixels
Battery: 3650mAH lithium polymer battery
Features: Side fingerprint identification 丨 屏 前 摄 摄 2 22.5W Fast charge 丨 Super NFC
Motherboard IC information
After analyzing the whole machine components of glory 20, the overspeed cost is about $ 256.45, of which the main control chip cost is about $ 136.20, accounting for 53.1% of the whole machine cost. This small e jumped over the disassembly and let me talk about the motherboard IC information.
The main IC of the motherboard (below):
Red: hisilicon-hi3680-unicorn 980 eight-core processor
Yellow: micron-8GB memory
Green: Samsung-KludG4U1EA-B0C1-128GB flash memory
Cyan: Hisilicon-Hi1103-WiFi / BT / GPS / FM chip
Blue: hisilicon-hi6526-charging management chip
Magenta: Light sensor
The main IC on the back of the motherboard (below):
Red: hisilicon-hi6421-power management chip
Yellow: hisilicon-hi6405-audio amplifier
Green: 2 hisilicon-hi6422-power management chip
Cyan: hisilicon-hi6353-radio frequency transceiver
Blue: 2 hisilicon-hi6h03s-low noise amplifier
红: qorvo-rf5216a-transmission module
Light red: qorvo-qm56022-front end module
Light yellow: Bosch-BMI160-gyroscope + accelerometer
Light green: AKM-AK09918-electronic compass
Light blue: Goertek-microphone
Shallow purple: NXP-PN80T-NFC control chip
Be
The logic, Memory, PM, and RF chip information used on the motherboard are shown in the table:
The MEMS chip information used on the whole machine is shown in the table below:
Dismantle
Retransmission to the dismantling, first use the lock to take the plastic card to take the plastic card, and then use the hot air gun to a certain temperature, use the cladder to be opened from the rear cover edge to remove the back cover. Carto does not use waterproof rubber circles.
The rear cover is fixed by a circle of foam, and the back cover is posted on the motherboard position with a heat sink, and the post-visual position is posted with a circle of foam, which is dustproof and buffering.
The frame of the PC + GF material is fixed by a buckle, screw and foam. The frame is relatively fragile and easy to break.
Remove the NFC coil and flash soft board fixed on the frame, the NFC of glory 20 not only supports traffic cards, but also supports community access card, home smart door lock card, hotel room card, etc. There is no buffer cuvine corresponding to the BTB interface on the frame.
The battery is then removed, and there is a detailed dismantling step on the battery. Torn the battery when the battery is removed, and then the 3 pulls the battery can be removed separately.
The battery is 3.82V, 3650mAH lithium polymer battery, and the battery cell manufacturer is ATL.
Then disconnect each BTB interface to remove the motherboard, panel, main panel connection soft board, speaker, camera, and RF coaxial line. A heat conductive silicone is attached at the motherboard CPU position.
The fingerprint recognition soft board is then removed. Button soft plate, distance sensor soft board and handset.
Side fingerprint recognition soft board and button soft plates are fixed by screws, and the side fingerprint identification and buttons are not integrated, but are connected to the motherboard separately.
Finally, a large area of heat-dissipating graphite sheet is attached to the inner support by the heating screen.
The screen uses TIANMA's 6.26-inch TFT excavation screen. The resolution is 2340x1080, and the model is TL062FVMHO2.
The whole machine uses 21 screws, and there is a tap label on the screw. Equipped with TFT LCD, the LCD screen has not yet made a fingerprint, so glory 20 uses a side fingerprint. In terms of heat dissipation, the inner support, the rear cover and the battery position have a heat dissipation graphite, and the CPU is heat-dissipating heat through the heat-conducting silicone. The internal structure of the whole machine is simple and easy to maintain. Its cost is mainly reflected in the part that can be seen.
Source: ewistech
Our other product:
